Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Need engine help


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob Brademann on February 08, 2004 at 06:02:04 from (162.40.248.54):

I need some advise. The knowledge on this site is amazing. I have torn down the engine of my 1945 A. I found the block was cracked between the middle two cylinders across the water jacket. The crack continues on both ends and stops at the sleeves. It is impossible to see how far into the block the crack goes however it has apparently been that way for some time; there is erosion across the top of the block from water jacket cell to the next, but does not extend to the sleeves. There is no external crack. I would like to have re-sleeved the engine and replace the pistons, rings and bearings. Now I have some concern as to whether I could remove the sleeves without further damaging the block. Question is, the sleeves look glazed but not scored. One of the pistons has some scoring. Can I hone the cylinders and purchase oversize pistons? I guess true to IHC history, the engine really ran well but missed occasionally and burned some oil. The rest of the tractor has been visually restored to parade quality, which is all I ever intended for the project. Along that same line, the tappets are also worn to the point that it would seem to be difficult to properly set lash after I’ve re-valved the head. Can the tappets be resurfaced or do they need to be replaced?

You guys seem to have experienced it all when it comes to these machines and your help would be greatly appreciated. My daddy was a Farmall dealer in Minnesota and I somewhat cut my teeth on them but I never got into a total engine overhaul.

A-Bob



Follow Ups:




Post A Followup

:
:

: Re: Need engine help

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy