Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Need engine help


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Tom of Minnesota on February 09, 2004 at 19:07:14 from (165.247.253.103):

In Reply to: Need engine help posted by Bob Brademann on February 08, 2004 at 06:02:04:

Bob,
I had a similar problem with my B. For some
time, it was leaking coolant into the oil. I finally
pulled the head and discovered a large crack
running from the inside of the #1 cylinder to
the inside of the #4 cylinder. I didn't think the
water was getting into the oil through the
crack, so I called a Farmall mechanic friend.
He said to drain the oil, pour coolant into the
water jacket and place a container under the
oil drain. The next day, the container contained
several tablespoons of coolant. I repeated the
test several times, with the same results each
time. This meant the O rings on the wet
sleeves were bad. My friend said that, years
ago, they used to fix cracks like this in Allis
Chalmers and Farmall blocks by drilling a
hole through the entire block between
cylinders #2 and #3 an inch or two below the
top. Then they'd insert a threaded bolt. The
old-timers would then put some sealer on the
ends of the bolt, slip on a washer or two, then
add a nut on each side and tighten them until
the crack squeezed together. He said this
would hold things in place for a long time. But
because my O rings were leaking, I decided to
find a used block and then had a machine
shop build me a new engine. It cost 10 times
more than I paid for the tractor when my wife
bought it for me back in 1972, but I didn't care.
After all those years of yeoman service, I just
couldn't abandon the old girl in her time of
need. Now she runs like a young colt.

As long as your A wasn't leaking coolant, you
might get by with the old block. But I wouldn't
weld anything. Several experts told me that
once you weld a block, you have to have it
re-machined to make sure everything is
square and true. It's not cheap, they say. Try
patching yours. It might last for years. Good
luck.



Follow Ups:




Post A Followup

:
:

: Re: Re: Need engine help

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy