Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Engine swap or rebuild?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by wdTom on July 10, 2003 at 17:05:29 from (155.212.222.117):

In Reply to: Engine swap or rebuild? posted by Farmer in the Dells (WI) on July 10, 2003 at 10:06:29:

I would inspect the spart engine carefully, stored for 10 years, you never know. If it was in a stable temperature dry place maybe. It could be stuck by now if in a damp place or changing temperatures. Did you turn it over from time to time? Did you pour oil into the cylinders from time to time? Check it carefully.

The running engine. If the clutch isn't slipping, I wouldn't worry about it. They last a long time if you don't ride them. Grease the throwout bearing once a year or so and don't worry. The front seal is easy if you support the front of the tractor and take off the front end stuff. Even if you have to pull the head and have it done, that isn't hard with the hood off. Get a reprint of an AC service manual. As for removing the engine , if you support the rest of the tractor it too isn't hard. If you do replace the clutch the only thing to do is to make sure the clutch plate is lined or centered when you bolt the clutch pressure platae to the flywheel, you need a dummy clutch shaft to do this, make it out of a wood dowel. Turn it to fit the pilot bearing, then the inside of the spline in the clutch disc, use it to line up the clutch disc as you bolt up the pressure plate. The closer you get it the easier time you hav getting the engine to slide onto the real clutch shaft in the torque tube later. You need a way to lift the engine and then roll the back of the tractor away from it. It helps if you do thes on level paved surfaces, but smooth level dirt or garvel is ok too. Be very carefull if you try to remove the engine and front end as an assembly, it is very unstable. Better to do it is peices especially as you need to get to the front seal. Ask here if you have more questions. Or go over to the orange page.


Follow Ups:




Post A Followup

:
:

: Re: Re: Engine swap or rebuild?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy