Posted by Bryce Frazier on October 07, 2014 at 16:53:33 from (67.142.182.23):
Alright, so I have a few questions about running gear...
I posted this first picture of my running gear on here before, looking for a manufacturer, but there was a lot of mixed-emotions about it, and we all kind of decided that it must be a David Bradly, but I was fumbling around on the internet today and found this particular ad showing a Dearborn 21-2 Wagon, and to me it is IDENTICAL!! You can even see on mine where the front bolster was, and at some point was removed...
Have a look and tell me what you think! Are they the same?
Also, if it is indeed a Dearborn 21-2, who made it? Electric wheel co?
Next question would be, someone has made mine so that it isn't telescopic anymore, and I want it to be shortened up a little bit, and then I want to put a deck on it. I at that point don't care if the length can be changed, BUT as it is right now, it doesn't have a way for it to flex, so if you go over a little bump, one wheel comes off the ground. Soo, what can I do to make it flex?
I have been looking at some of the pictures online, and I think I have a solution, but I want to see what you guys think..
Say for example, the tube they welded in is 2 inch, if I were to cut in nicely in the middle, then slide a 3 or 4 foot section of the next bigger pipe over each half, then put the halfs back together with the 3 or 4 foot section of pipe, not welded, just sitting there.
Next, I found a way to cut an oval shaped hole in each end of the bigger pipe, and I cut through the smaller pipe as well, and then put a grade 12 bumper bolt and nylock nut on each end?
Then, the larger hole in each end would allow the wagon to flex as needed, and would still be plenty strong enough for a load?
Next, it says in the add that the may payload is 5000LBS, does that seem like a safe load to haul, provided that the tractor can handle it? Thanks, sorry it is a little long, but remember, I am just a kid, and kids ask a LOT of questions, or at least my mom says so... :) Bryce
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.