Farmall & IHC Tractors Discussion Board |
Re: 656 remote leak
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by K.B.-826 on October 24, 2005 at 16:38:56 from (66.188.223.190):
In Reply to: 656 remote leak posted by PennsMike on October 24, 2005 at 14:47:53:
Sounds to me like your detent piston o-ring is leaking. The piece you describe as a "screw on cap"- this is a large plug screwed into a short length of large pipe, and the pipe screws into the remote valve body, right? And the piece you describe as "pressed into the cap and 1/4" in diameter", if you pry it out and look inside, do you see what looks like a flat-headed screw head? If so, we're on the right track. To repair, disconnect the control lever from the spool at the front of the valve, next, unscrew the piece I describe as a short length of large pipe from the back of the valve. Now you can withdraw the spool and detent assembly from the valve body from the rear. Clamp it in a vise by the piece I describe as a short length of large pipe, and unscrew the large cap from the end. Keep the parts in order, and remove everything from the end of the spool. At this point you should be left with the spool and the detent body. Unscrew the adjusting screw from the detent body and remove the insides, being careful not to lose the balls. Now clamp the spool in the vise by the very end where the lever attaches, and using a punch as a handle, unscrew the detent body from the spool. You should now be able to remove the tiny detent piston. Get a new piston w/ o-ring from your Case-IH dealer, plus the two o-rings that seal the spool to the valve body, plus the o-ring that seals the detent body to the spool. Assembley is the reverse of removal, when you're done you'll need to adjust unlatching pressure, you'll need a 5000 psi guage for that. This job is much easier than I make it sound, but I haven't had one apart for a year. An I&T manual will really help you.
Follow Ups:
Home
| Forums
Today's Featured Article -
Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|