Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Cub 184 very frustrated


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by lee on July 25, 2004 at 19:37:53 from (24.24.95.246):

In Reply to: Cub 184 very frustrated posted by Dieselrider on July 25, 2004 at 14:12:49:

Yes, I would agree the unit should be torn down, cleaned, inspected and repaired as required. The long rock shaft that comes out of the gov housing is supported by a needle bearing on the side where it exits the housing, a blind hole on the far side of the housing internal and also runs thru a third bracket on the left side of the tractor where the throttle rod hooks up. There is plenty of opportunity for this shaft to bind if bent slightly or worn bearings or the bracket out of alignment. The needle bearing may be worn into the shaft causing a bind or it can bind where it runs thru the external bracket. There is another lever on a pivot pin that couples the throtttle lever thru a spring to the rock shaft. This lever must be free to move and the spring of a specific length and spring rate. Not just any spring works there. Internal there are several other moving parts: fly weights held on a shaft by pins and a thrust bearing to impart motion to the rock shaft. There is also a second spring. These can also give trouble if excessively worn or perhaps broken. If you have not been able to adjust it there is obviously something wrong with it. But it is a simple device and can be repaired. I would not cut corners in repairing it as the governor is a key element in the proper working of the tractor. Your effort will be well spent.


Follow Ups:




Post a Followup

:
:

: Re: Re: Cub 184 very frustrated

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy