Farmall & IHC Tractors Discussion Board |
Re: Re: Re: 414B ENGINE
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by jdemaris on April 06, 2004 at 19:03:36 from (209.23.28.87):
In Reply to: Re: Re: 414B ENGINE posted by Greg on April 06, 2004 at 07:56:53:
I'm referring to the BD series diesels. I assume BD stands for British diesel. My first experience was from a B275 I bought at auction. It had water in the oil, bad crank journals, etc. When I pulled it completely apart I found cracks in the crankshaft main-bearing webs. Major cracks that were beyond repair. Also found many stress cracks in the cylinder head all around the precombustion chambers. When I began searching for a good used block, all I found were also cracked in the same areas. After looking a half a dozen used blocks that were ALL cracked, I finally seemed to have found a good one. It was a BD144 that had been put into a B414. The original BD154 had gotten a cracked block and the owner bought a Central Tractor "rebuilt" block. That was the one in it, and the one I bought. After getting it home, and steam cleaning it, I discovered that it too was cracked in the same spots but had been welded, then covered with Bondo, and painted - i.e. the repairs were hidden. That's the block I've been using ever since because I was never able to find one that was better. I have to assume there is a design flaw in the block. I also noticed, when assembling the engine, that the connecting rods don't have any positive method of locking the caps. Most modern rods have dowels, or slots, or fractured surfaces to keep rod caps from shifting. These rods have nothing. So, I consider the engine somewhat low-tech and low-engineered. It's also a poor starter as far as diesels go. So, I love the tractor that it's in, but don't have a lot of faith in the engine. I've probably got 500 hours on it since I put it together. Only time will tell how long it will last, but I don't expect 10,000 hours out of it.
Follow Ups:
Home
| Forums
Today's Featured Article -
Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|