Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  

Re: Allis chalmers 7040 hard start diagnosis help.


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by chevy hal on September 23, 2009 at 19:29:14 from (98.125.253.94):

In Reply to: Allis chalmers 7040 hard start diagnosis help. posted by ben brown on September 23, 2009 at 15:10:34:


ben brown said: (quoted from post at 15:10:34 09/23/09)
chevy hal said: (quoted from post at 11:55:05 09/23/09) I ne
you are a 180 out on timing they well run sorta so change timming and on your 190 high clutch pack is out also when thes tractor get old the rubber pads that are under the deck wear out and make it hard to adjust the linkage on hi lo


Hi Ben. Well I rechecked the timing by removeing the # 1 injector and turning engine untill compresion stroke 16Deg BTDC. then i removed timing cover on pump and timing marks are aligned. Just to make sure mark was on #1 injector, I removed line from pump then bolts from pump gear and turned pump one revolution. when the timing marks lined up in the pump window , fuel came out of the #1 line fitting on pump.

Am I wrong in the way I am checking the timing? Found out today that this pump is two years old. Note: the marks in the pump window, only one is stamped on the rear disc. the one on the front is eched with an engraver by the rebuilder, not stamped. Don't know if this makes a difference or not. Do you still think I should turn the pump 180 deg? or look elsware. I don't know what you were refering to in the last part of your reply though. thanks , Hal.


Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy