Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Pulled Head no clue why zero compression in 1 Cylinder


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Ken McWilliams on October 23, 2000 at 09:38:26 from (38.232.245.127):

In Reply to: Pulled Head no clue why zero compression in 1 Cylinder posted by Rick from Paso on October 22, 2000 at 23:09:02:

Rick,

I think you may have gone a little fast for me.
You were able to put compressed air into each cylinder and each held pressure?
The engine, however before tearing down has a miss?
When cranking the engine, the subject cylinder developed compression at or near the other cylinders?
Oil in water and oil in cylinder could be a long term problem, but don't jump to conclusions yet.
If the above are true, then look at dead spark plug and non-acutated exhaust valve.
A dead spark plug will allow fuel and oil to accumulate on top of the piston. Check for spark through the spark plug's gap and then at the end of the wire.
If good spark, check for the exhaust valve properly being actuated. You will get good compression, but will not exhaust if the valve is not properly going up and down. The exhaust valve could be closed all the time which accounts for the no leak-down and good compression value. Cam lobe could be worn off, or bent push rod, or lifter or push rod not properly seated but off to side.

The oil in water could be a bad head gasket that is allowing seepage, but may not have been the reason that it was not running properly.

You may need to put the head back on with the old gasket and finish your diagnosis. Use thick greas on the head gasket as a temporary seal until the diagnosis is completed.

I can't determine your problem until more data and observations are gathered

Ken McWilliams
Dayton, OH


Follow Ups:




Post A Followup

:
:

: Re: Re: Pulled Head no clue why zero compression in 1 Cylinder

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy