Tractor Talk Discussion Board |
Re: magnets
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by MikeH-Tx on July 27, 2000 at 11:42:34 from (192.55.24.50):
In Reply to: magnets posted by Jim in N M on July 26, 2000 at 20:03:04:
Jim, something to concider. When we were building our house, I looked into the same item. However, many of the nails and junk were left too close to the house to be practical to use the tractor. Also, there is the matter of tractor tires not liking nails. I decided to make a hand operated magnet to pick up the nails. It worked so well, it might be of interest to you. After looking at Northern and other sources of magnets, I didn't like the cost of the really powerful ones. Turns out, there is a source of free, very powerful magnets: dead disk drives. They have some of the most powerful magnets you will ever see inside them, to control the read/write head. And, the nature of disk drives is such that dead ones are plentiful. I opened the drive by using a dremel cutoff wheel on the case machine screws to adapt the heads to a standard screwdriver. I just ground a slot into them, marring the case as well (who cares). Then, only a couple of screws inside need to be removed to dismantle the innards (a couple to get the disks themselves out of the way and a couple holding on the magnets). Since this is not a repair job, care does not need to be taken. As near as I can tell, nothing inside a dead disk drive except the magnets are of further use. You will find either one or two magnets, mounted to nonmagnetic metal brackets, at the base of the read/write arm. Since these magnets are made of a powdery material (lanthanum?) that crumbles easily, I coated mine in a thin layer of epoxy and at the same time molded on an eyebolt to the back of the bracket to attach a thin rope to it. Thus, I created a magnet on a rope. The epoxy also helps you clean the magnet of metal filings. All this sounds like a lot of work for just a magnet, but these are not just magnets. If you get your fingers between the two magnets and get them too close together, you will get a nasty bruise when they snap together. It is also difficult to get them apart. You have to slide them - no way can you pull them apart. They are that powerful. I then just dangled the magnet at the end of the rope and with a sweeping motion walked around and picked up all the nails. After collecting a handful, I would clean the magnet, drop nails into a bucket and start over. Try it. Amaze your friends. Pick up nails. Enjoy.
Follow Ups:
Home
| Forums
Today's Featured Article -
Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|