Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Rescued VAC-Stuck Ring?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by RAB on May 01, 2007 at 23:25:03 from (195.93.21.42):

In Reply to: Rescued VAC-Stuck Ring? posted by JRT on May 01, 2007 at 20:20:40:

JRT,
You wrote: I think maybe the ring is stuck

I ask: how much is no compression?
Have you carried out a compression test - both dry and wet? Until you do we have litle in the way of hard facts to go on. If there is no compression at all it could be a hole in the piston. It should not sound too good either. All these things are very subjective - no hard facts/information, so you need to find out as much as you can before deciding on the most likely route for repair.

Personally, as it will have about 4 rings on each piston I doubt you have seen inside an engine? (as you say "the ring is"). No problem - everyone has to start somewhere, but understanding the basics is easily found in a book.

When an engine sits an exhaust valve will always be open and like as not this may not be sealing correctly after several years. It may be sticking or the head/seat rusted (we don"t know the conditions it has been in for the last several years). It may have a broken valve spring, a burn"t valve (from before it sat), a sticking stem stopping it closing properly, a cam lobe worn out (so too little valve lift), a broken or otherwise valve rocker. The inlet valve may have been open as well and that too may have problems ( a cylinder with just an inlet valve open is usually protected by the oil bath aircleaner).
So upshot of all this is that is is useless soaking it in anything if the fault is a chipped valve or similar, so investigate a little further first.
Hope this helps.
Regards, RAB



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy