Tractor Talk Discussion Board |
Re: Hey Allen in NB Buick Transmission again
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Brokenwrench on August 09, 2006 at 05:47:29 from (69.128.197.103):
In Reply to: Hey Allen in NB Buick Transmission again posted by IA Roy on August 08, 2006 at 19:49:51:
Hello Roy, It`s hard to go by case casting numbers, even the GM parts guys can`t tell you what they mean. If I follow you right, you dropped the used tranny, want to disassemble both and put the guts in the burnt out one. If you`re gonna tackle that, you may as well get an overhaul kit, cause you`ll ruin the channel plate and valve body gaskets for sure. I don`t know how familiar you are with these units, but their not a real quick easy tranny to work on. If you haven`t done one before, the likelyhood that you`ll miss something is pretty good. That`s not an insult, just the GM front wheel drives aren`t like anything else out there. I would suggest, cutting your losses and finding a different used one. The 91 is the early 4T60E, at worst, you may be running alittle different gear ratio, or stall speed. In 91 the computer shouldn`t pick it up. In some of the later ones, if the gear ratio was changed, the computer would think the tranny was slipping. BTW you don`t want to press out the converter reactor, it`s bolted in from the front. Whatever you do, I definately agree that you don`t want to mess with much in that dropped tranny. I`ve seen em drop on one side and crack on the other. Plus there easily could have been damage to internal parts as well. Jsut wondering, how did it fall to break the converter reactor? That`s pretty beefy, and it`s tucked way back in the bellhousing. Good Luck, maybe Allen will jump in with some sound advice for ya. Later Brokenwrench
Replies:
Home
| Forums
Today's Featured Article -
Harvestin Hay: The Early Years (Part 2) - by Pat Browning. The summer of 1950 was the start of a new era in farming for our family. I was thirteen, and Kathy (my oldest sister) was seven. At this age, I believed tractor farming was the only way, hot stuff -- and given a chance I probably would have used the tractor, Dad's first, a 1936 Model "A" John Deere, to go bring in the cows! And I think Dad was ready for some automation too. And so it was that we acquired a good, used J. I. Case, wire tie hay baler. In addition to a person to drive th
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|