Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: How many HP for bailing hay? Square Bales


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by TimV on March 26, 2006 at 06:12:10 from (24.59.208.200):

In Reply to: Re: How many HP for bailing hay? Square Bales posted by Marksd on March 25, 2006 at 16:38:27:

Mark: Actually, you probably don"t need an overrunning clutch, as many (in fact, most) balers already have one. An ORC is typically a small additional section of shaft that attaches to your PTO stub, and from there to the PTO shaft of your implement. It is designed so that power is transferred from the tractor to the implement, but not from the implement to the tractor. This is necessary when the implement is one that stores energy (such as bushhog with large, heavy spinning blades) and would then release that energy as it "wound down" after the clutch was pushed in. Unfortunately, with many older tractors, pushing in the clutch does not decouple the PTO from the transmission gear train (though it will decouple it from the engine) and so the momentum stored in the spinning blades would continue to push the tractor forward with no way for the operator to stop it. On most balers, there is an ORC built into the flywheel, so one is typically not needed at the PTO. If you have a chance to watch a baler being run, have someone push in the clutch of the tractor (or otherwise stop the PTO) and you"ll hear a "click-click-click" from the flywheel. This is the ORC, which is preventing the flywheel from pushing the tractor. Should your baler not be so equipped, any farm store (TSC, Farm & Fleet, or any tractor dealership regardless of color) should have PTO-mounted ones for under $50.00.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy