Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: building a shed w/tarps


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by T_Bone on August 10, 2005 at 08:23:48 from (4.240.42.217):

In Reply to: building a shed w/tarps posted by Poor guy on August 09, 2005 at 12:20:19:

Hi PG,

I think the tarp idea is a waste of money as it won't last long in the wind.

Me, I would spend the same money on metal track (use for all framing including studs)( no metal studs, very thinn gauge) as there a heavy gauge and will last. Then use 28ga corragated sheeting for the roof and walls until you reach the same dollar value as the tarp cost.

Example: 10ft wide x 12ft long x 10ft high, 1 open end

23- metal framing track 2x4x10ft= $46
23- 2ftx10ft 28ga sheeting = $276
Box #7 x 3/4" metal screws= $5
tin snips= $15

Total= $342 at HD prices for a all metal shed, less door, door $100 more.

Have a hill side? Free shed for the digging and scrap lumber.

Build a sod shed. Turn a 10ft square of dirt. Mix dirt and 6" of Water and let stand. The next morning skim off the clay and set aside, then water 6" again, mix and let sit, skim off the clay. Repeat for enough clay.

Now mix 14% clay by volume, dirt, pea gravel and straw. Pour that mix into blocks and let sun dry.

Build shed walls with the blocks laying flat.

To build the roof, pour 8" x 12" x 4" thick blocks. Start on each corner by using blocks layed flat, then use a mortar mix of 14%clay and sand to build up a taper bed for the next block and lay the next block to the inside by 1/4 of block width, continue with the next layers until the blocking is layed on the 4" edge on all four coners. You should now have a open dome roof. Use the blocks on the 4" edge to finish the open dome. Finish the roof with a mortar mix of 14% clay sand mix.

To water proff inside and out, use diesel to fire blast the inside of the building to 2000º for 24hrs, about 25gal of diesel required. I won't go into details on the homemade burner but just pipe fitting and a ball valve with a 55gal drum 10ft in the air.

T_Bone



Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy