Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Off topic, Chevy truck help!


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bryan in Iowa on January 20, 2005 at 19:40:21 from (64.12.117.7):

In Reply to: Off topic, Chevy truck help! posted by knauffj on January 20, 2005 at 12:21:32:

Well, where do we start ? Ok I'll take stab at this .I get lot of calls during the week like yours.Over the phone diagnoisis is lil tuff,,lol.
First thing , stop throwing parts at it ! Fuel pressure on these has to be exact, not oh its getting fuel , or yea it sprays out injector . Check fuel pressure key on engine off,write it down ! Watch pressure as it peaks,note how fast it falls off , and where it ends up . System should hold residule pressure after pump stops. If falls off quickly you need to pinch return line and retest . If pressure holds now, you have reg stuck open or leaking . If pressure still drops after pump stops, possible injector leaking, or bad in pump check valve , can check by pinching off supply line ahead of pump, if stable ,,bad pump. Also you should run fuel pump volume test. There should be a wire to energize fuel pump.Open supply line , energize pump,should just about fill pop bottle 3/4 full or close to it in 30 seconds .If low , check pump, filter , line restrictions ,etc..That pretty much is complete fuel pressure test . Make note of pressure when cranking , running , and when truck dies . Any changes indicate pump shutting off . But you should still be able to keep pump running by prime connector .
Next thing I'd look at it engine vacuum. Should be steady , at least 12 inches, any less and you have either timing problem , timing chain jumped , ignition timing off, or valve spring problem , or plugged exhaust . Double check ignition timing,,MAKE SURE you unplug timing connector , either on firewall or under heater box on pass side in cab . Very important , if not unplugged timing can be off as much as 30 degrees . TO check back pressure either pull oxygen sensor and put gauge in there ,,or just drop pipes down from manifold 3/4 to an inch . If runs okay ,pluuged exhaust, converter etc . Also look at Egr,,if stuck open acts like big vacuum leak . Low vacuum will make map sensor fatten up fuel mixture , run pig rich .
Okay if have good manifold vacuum , next I'd wanna see what Injector pulse width is . If you have diagnostic scanner that will show it , you should be seeing around 1-4 mil at idle . If it is way more than that computer is tryign to fatten up mixture 10.0 - 18.0 milsec is pretty rich. More likely vac problem still if that high . Also Map sensor voltage should be close to 1.2- 2 .0 volts at Idle . if up around 3 -5 v either map is bad , or reading low vacuum,,you can fool Map sensor with handheld vac pump, hook up to port put 20 inches to it , see what happens ? If runs ok,look at causes of low vacuum.
Few other thing to check out .These trucks are famous for distributor shafts getting magnatised, makes em run like crap . Weak module , weak coil .
Sorry for the long rant , but these are great motors. You just need to have all your ducks in a row before you start slapping parts on em or asking a tech "whats wrong with it ?" with out having done some basic testing and results to go by . I see it in my shop all the time . Most of the time we get it fixed , few that bite us , but keep after them tiil they're back on the road . If you still having problems , shoot me an e=mail ,,can see what we missed or you can give me phone call . Good luck
Bryan


Follow Ups:




Post a Followup

:
:

: 65534p> :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy