Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: what is a relay?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by txblu on November 15, 2004 at 06:11:09 from (199.46.199.233):

In Reply to: Re: what is a relay? posted by StuBC on November 14, 2004 at 17:46:11:

The purpose of a "fuse" is to "fuse" in case of a circuit short or other "current" overload. If it weren't for a fuse, the conductors would overheat and melt insulation which would allow wiring to short to other wiring and you could easily wind up with a fire.

The fuse is usually rated for 1.5 times the normal current.....if you need 10 amps to run 2 headlights, put in a 15 amp fuse and size the wiring accordingly which is 14 awg (good rule of thumb). IF your headlights are 35watt and you have 2, and a 6 volt system, you are right at (tad over) 10 amperes [if wired in parallel...one side of each to the fused wire (via light switch) and other side of each to chassis ground]. 12 volt system is half that (if you are using 12v lamps). You could still wire up with 14 awg and use the 15 amp fuse however.......you're protecting the wire (usually), not the thing using the power; however it does get protected also.

Now you could send a 12v wire to 2ea 6 volt 35 watt lights and wire the lights in series across the 12v input (12v hot....from the 15A fuse) to one light then other side of that light to input of the second light (not ground) and the output of that second light to ground). In that case the 14 awg wire would still be correct.

You can get fast blow and slow blow fuses. Slow blow fuses are designed to hold on higher than normal current (overload) for a few seconds.....like when a motor starts.

Even though a lamp usually has about 1/10 the normal resistance when cold, and hence a 10x inrush of normal current, it is very short in duration and in a tractor, a normal blow fuse usually is adequate.

And that's the rest of the story (Paul Harvey)

Ask another question.

This is fun.

Mark


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction, ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy