Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Radial tire familiarity


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Old Ford Mechanic on September 16, 2004 at 11:12:16 from (65.81.216.28):

In Reply to: Radial tire familiarity posted by txblu on September 16, 2004 at 05:55:13:

First thing to do is check all parts in the steering system.This includes wheel bearings,spindle bushings,thrust bearings,pivot pins and bushings,all tie rod ends,backlash on worm and sectors in steering gear ect.Then make sure you have an equal amount of air pressure in the tires.If you have 16lbs in right rear make sure the left rear has 16lbs.Same deal on the front,if you have 35lbs in the right you want 35lbs in the left.If you have ballast on one side you want the same amount on the other side.Also a worn tire will make a difference in wheel pull.To set the toe on a tractor.Park the tractor on a hard level surface such as a concrete floor.take a 4 ft. level and plumb the centerline of the tire by aligning through the center of the grease cap on the wheel hub.Align the bubble in the level and make a chalk mark on each end at the front and the rear of the tire.Do this on both front tires."Do not jack the tractor up" Finally,take a measurement at the rear side of the wheels and one on the front side of the wheels.Some mechanic's like to measure from center tire rib to center rib on the other tire but i prefer to measure inside of rim to inside of the other rim.When properly aligned the front measurement such be 1/4" closer than the rear measement.Adjust this dimension with the tie rod ends."DO NOT BEND RODS" Camber and caster are not adjustable.If all the bushings and related parts are not worn these dimenisons will be right.I've been adjusting toe in for 35yrs using this procedure and have never had any steering "wander" or "tire wear" problems.


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy