Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Implement or 3-rib tires - Farmall 560 with Loader


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Brent in Iowa on June 20, 2004 at 21:35:27 from (66.43.236.169):

I just put a new 3-rib 6.00-16 tire on my 560 last fall after putting 16 thorns into the old one while mowing some brush. Yesterday I was over at the neighbors moving manure and "found" a broken metal fencepost with the 6.00-16 on the other side (good thing it wasn't the new one), boy did I lose air fast!

In order to finish (tire store closed) I took a brand-new 15" spare implement wheel/tire from one of my grain wagons (only one I had with right bolt pattern) and threw that on. It was same overall height as the 16" tractor front, but a tad wider.

My question is: I now have to buy one new tire/tube to get a matched set on the 560, should I buy another 16" tractor front (6-ply on there now) or another 15" implement tire (8-ply now). I have a loader on the tractor and was thinking the implement tire may be too bouncy (taller sidewall, more "balloonish" too), but it would be nice to have the extra flotation/less compaction in the hay field. I have never ran anything but 3-rib tractor fronts before. Am I going to lose traction when turning, or other issues to think about? I use it mainly for moving manure and snow.

Any thoughts would be appreciated.

Thanks!



Follow Ups:




Post a Followup

:
:

: Re: Implement or 3-rib tires - Farmall 560 with Loader

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy