Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Re: Re: 4020 hydraulics


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by jdemaris on November 22, 2003 at 15:48:00 from (209.23.29.101):

In Reply to: Re: Re: 4020 hydraulics posted by kevin on November 22, 2003 at 06:07:25:

If you've checked the obvious things, that it probably is your pump. I find it to be a fairly easy unit to rebuild, but getting it out is not easy. On 4020s, I pull the front end off and pull the pump out from the bottom.
The most common wear item is the stroke-control valve which can be replaced without removing the pump (I was a field mechanic for John Deere and I've done many of them). 15-20 minute job when you're used to it. I also did their bench rebuiding for hydraulic pumps and fuel injection pumps). Complete pump rebuild, once on the bench, would take 2 hours and $120 in parts (on the average, back in 1989).
Back to the point, when the stroke control valve gets wear along its seat, it will make a hammering or chattering noise. Usually, it will also make the tractor start hard. Very often starter motors are burnt out because of worn stroke control valves. Gets bad enough, you will lose all hydraulics. New valve and seat assembly used to cost around $35, but I haven't worked for a JD dealer since 1989. I fixed many of them by just pulling out the valve itself (not the seat), and stuck into a valve refacer, refaced it, and stuck it back in. Very often it worked fine although I'm sure such repairs are not sanctioned by John Deere. If you do so, you MUST readust the stand-by hydraulic pressure. There a adjuster on the outside of the pump for this.
If you do remove the pump, it's not bad to work on. Has Timken style adjustable bearings, so bearing endplay must be adjusted with shims. You've got 8 pistons and springs to inspect, along with 8 discharge valves and 8 inlet valves that at least need to look at to make sure nothing is broken. As of course, as aforementioned, the stroke control valve is a MUST.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: 4020 hydraulics

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy