Tractor Talk Discussion Board |
Re: Gaskets?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Wayne on July 06, 2003 at 18:55:52 from (205.188.209.105):
In Reply to: Gaskets? posted by Sean W on July 06, 2003 at 00:09:28:
I've built everything from inline 6 cyl Murphy diesels, to 8V-92 Detroits, to Briggs and Stratton lawn mower engines, and I can tell you from experience that one of the most important things is to make sure that the gasket surfaces are clean. I always use the Scotch Rol-Lok discs for this. Just make sure you use the right disc for the type of metal to insure you just clean the surface and don't gouge it. As far as a sealer to put on the gasket, the best thing I've found, especially on oil pans and things like that is a THIN film of Ultra Blue or Ultra Copper. ANYTHING but plain old silicone, since it tends to squeeze out into places it shouldn't be and can block ports, etc, causing problems later. On larger gaskets that need something to hold them in place, then use something like Copper Coat as some have mentioned. Suprisingly enough on some of the "foreign" engines like the Yanmars, they don't even use gaskets, instead they use what is best described as a gasket compound that is almost like Loctite. You simply smear it on and assembly the part, and it seals from there. For head gaskets, it's not normally recomended to use anything unless the manual specifically calls for a sealer, and then it's usually limited to use around oil drain back ports, water ports, etc. Lastly as has already been mentioned, the correct torque is also important. Usually the factory torque specs take into account the diameter/size of the fastener as well as the length (affects how much it can stretch), as well as the grade, and also the material it is threaded into. If you don't have the factory specs, you can often use a standard chart as a guide, but even that isn't always reliable. Some mfgs don't actually give torque specs for things like head bolts, but rather rely on different methods such as streching the bolt,ie- giving a spec such as tightening to a specific torque and then going so many degrees tighter to strech it. It's things like this that can often make building an engine a challange. Still with time and experience it isn't all that hard. The main thing is to realize that somewhere out there somebody built it, and if your willing to ask questions, you can do just as good a job as the factory. Good luck on your future projects. Wayne
Follow Ups:
Home
| Forums
Today's Featured Article -
Identifying Tractor Smells - by Curtis Von Fange. We are continuing our series on learning to talk the language of our tractor. Since we can’t actually talk to our tractors, though some of the older sect of farmers might disagree, we use our five physical senses to observe and construe what our iron age friends are trying to tell us. We have already talked about some of the colors the unit might leave as clues to its well-being. Now we are going to use our noses to diagnose particular smells. ELECTRICAL SMELLS
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|