Tractor Talk Discussion Board |
Re: Re: Re: Re: how do you get johndeere to fill there tractor orders?
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by DAVE M on May 28, 2002 at 19:22:48 from (216.24.65.47):
In Reply to: Re: Re: Re: how do you get johndeere to fill there tractor orders? posted by Ahhh....the Valtra M100s would be comparable hp....by Woodbeef on May 28, 2002 at 18:02:28:
Well since you told him to cancel his order, and since Valtra is your favorite brand. I assumed you were talking about a Valtra. The Valtra brochere I have shows the M100 series and the smallest one (M700) at 70 PS HP, does not show the PTO HP as is typical of European tractor mfgr's. I assume that the PTO HP is around 60. They are nice tractors. Better than the JD 5000 series, comparable to the JD 6000 series. The JD 5000 series were designed to compete with the Ford/NH 30 series (3230,3430,3930,4630,5030) models. The Ford models were successful. Example 1965 4000 3 cyl 1999 4630 3 cyl. basically you could buy the same basic tractor for 34 years. JD could not beat them with a better tractor. example 2150/2155, 2350/2355, 2550/2555. Because of price. They brought out the 5000 series as the answer. Sold a bunch of them. NH countered with the TN series. As close of a clone of the JD 5000 series as you can get. The 5105/5205 Advantage series were brought out as a cheaper tractor to compete with the MF 231s, 240, and NH 3010 models when compared to them, it beats them hands down. 1 Increased hyd flow, 2 forward to reverse synchro shuttle. 2 examples. I priced one a 5105 2wd 1 scv at $15500.00 US dollars pretty good deal for a new tractor. Compared to $7500-$10000 for 20-25 year old Ford 4000's. I have seen priced. I have a 1994 JD 2355 MFWD 55 PTO HP wt: 8500 LBS. Built in Mannheim Germany. Excellent tractor no problems with it in 8 years. also a 1969 4000 Ford 8x2 independent pto 4800 Hrs never done anything major to it, 1 clutch, battery points (its gas).
Follow Ups:
Home
| Forums
Today's Featured Article -
The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|