Update all bushings and new shackles are in still waiting on the a new bracket. It was not as bad as I thought it would be lucky me my bud Mic stopped by I needed a third hand with the ball joint press. I used one of the drivers out of my new bushing driver set this bushing needed an extra bearing race as room was short on the back side. I made a tool to crimp the back side in like Ford did it would have worked if I had it out in a press. Now I understand why ford crimped the bushings in I will tack weld the pivot bushings in tomorrow for insurance.
On to the bushings on the ends of the leaf springs I was dreading it. The O.D. of the new bushing was 2.205 the bushing driver set had one 1.995 and one at 2.240. In my head I would thing the hole in the spring end was 2" so use the 1.995 well it wanted to cock off to the side when pressing. About this time Mic showed up with his extra hand I used the bushing driver that was larger 2.240. All was going well I pushed the old bushing out about a 1/2" stopped to swap back the the smaller driver. The driver was stuck I thought this can not be good. I did get it out by driving a screwdriver in this place on the end of the spring eye to spread it open are relieved the tension the driver came out..
HUMMM its not a closed link it has tension on it I put the bigger driver back in and forced the old bushing about 3/4 of the way out that is as far as the cup on the end of the ball joint press would let me go.
This is where dumb luck comes in I removed the press the old spring bushing fell out the oversized bushing driver has the eye of the spring opened up.
I put the new bushing in the spring it goes at least haft way in EZ till it hits the bushing driver I left in the spring.
I put the ball joint press back on with a piece of metal again the new bushing it drives in the new bushing the bushing driver falls out the other end life is good.
It feels good to see a tool you think will come in handy and it pays for itself the first time you use it Dumb luck...
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
