Posted by SVcummins on July 03, 2019 at 22:42:01 from (174.27.46.141):
In Reply to: Re: The cuber is here posted by casecollectorsc on July 03, 2019 at 20:10:09:
The new Holland went to scrap after I spent 3 days trying to untangle the chain and then the chain was shot and half the tubes were bent I swore I’d never own another apron chain baler ever again . So I bought a junk Hesston cheap wouldn’t even run finally bypassed all the junk computers on it and got it to run and pulled all the belts out and had them resized just need to pick them up from the dealer and get them put in also needs a new shaft it has a driven belt guide that runs off a chain needs one of them and it should run . talk about an over complicated pos let’s make a round baler that needs 2 brains and 15 miles of wire and switches to make a bale of hay when a new Holland or John Deere has a simple monitor the Deere of the same era will bale without the monitor even hooked up ran a435 for years with no monitor at all I guess that’s what I get for buying a fix it again tony fiat product ! Oh well it was cheap and it will run and bale hay eventually I still think it was better than fighting a worn out apron chain now if I had my old 851 back I’d take it even though it’s basically a round loaf stacker maybe a half notch above or below the first hawk built round balers that rolled the bale on the ground to form it but the thing would put up hay . And now I realize your talking about the D1000 it’s 60 miles from here and so is the tractor to run it and I haven’t had any time to even see what all Is wrong with it . And I could have used the ih 440 but I didn’t want the cow hay in little bales when you’re feeding 600 head a day the last thing you need is to pitch little bales into the mixer by hand every day .
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
