Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Case 1030 Loader.......


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Straw Boss on February 03, 2017 at 11:00:03 from (66.35.124.242):

In Reply to: Re: Case 1030 Loader....... posted by banjoman09 on February 03, 2017 at 06:27:55:

I hire my major mechanic work done because I ain't too swift but I'll help where I can.

I would say the most important thing to do first is be sure of your circuits.
As others said, a Case 30 series requires a remote on each side as a circuit instead of both on the same side.
Some guys who ran other brands couldn't get used to this and may have rerouted the lines on your tractor
before you got a hold of it. I would suggest you go get a cylinder and hook up your hoses and see what it does. If it acts like it only has power one way and the other acts like a float position, then you may have the two remote circuits criss-crossed. You should have power going both directions.

Second thing to do once you have your remote circuits "paired" is to determine which direction the flow is going. Most everyone hooks up in a way that the implement will raise when you pull back on the lever. If it doesn't, simply
switch the hoses at the remotes to reverse the flow. If you don't have a spare cylinder to check this, then just back up to an implement that has one and hook the hoses up. No need to actually hook up to the drawbar.

Once you have your cylinder working the direction you want, extend the cylinder all the way out and then go to the rear
of the tractor and simply try to twist the hoses at the remotes. The one that's tight is your pressure side. (Once you bump the hydraulic lever down it will loosen and the other hose will get tight.) If it's not the way you want to run it just switch remotes at this time, meaning if you want the loader circuit on the outside lever vs. the inside lever, switch to the other set of remotes. If you want the lever to power the loader hydraulics when its pushed down rather than up, then just flip flop your hoses within the same circuit. To my knowledge I don't think it really matters which way you supply power on these older tractors. It's the same pressure and detents either way. Newer tractors have a built in float position so pulling back is always the up position or power position on those systems.

So by now you should have determined which lever you want to use and which direction you want to pull the lever to put pressure to your loader spool valves as you may have to tie it back to hold it into position because the detents aren't likely to hold it there during loader operation. And now that you know which hose is the pressure side when the lever is pulled, that's the hose you want to run to the spool valve. Most I've seen have the pressure side come in on the left near the main loader lift lever. Second lever being the bucket tilt and the third being the grapple. Then the discharge line coming out the right side and returning to your tractor remote. I'll add that the main lift is usually on the left because again, most I've seen have a float position built into the valve body for loader work.

Helpful tip: Hydraulics on a 1030 are a breeze to couple and uncouple because you don't have to get on and off the tractor to bump the levers to relieve pressure. Just reach under the fuel tank and give the linkage a nudge the direction you want it to go. I wished I could do that on my newer tractors.

Since I tend to ramble, just keep asking questions as I probably only confused you.


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy