Posted by JD Seller on June 24, 2015 at 21:47:38 from (208.126.198.123):
In Reply to: Why not metric ??? posted by da.bees on June 24, 2015 at 20:17:02:
You may think metric is the way to go but it makes working on machinery a real PAIN!!! There are three "common" thread pitch standards in metric and 5-6 "special" pitches besides them. It makes the cost of keeping hardware to repair things be quite high. I keep two of the most common thread pitch standards and just those two make me have an extra $2500 in hardware that still does maybe 60% of the total "metric" stuff I work on.
I look at it the other way. Way back in the 1980s when this nonsense started we where easily the largest economy in the WORLD. Why the heck did the morons in charge think we needed to change to make all the "little" economies happy?????
So now we have a half breed system that has you having metric and English fasteners on the same machine. Don't think the stuff from the "pure" metric countries is all metric either. Many pieces have both on them as well.
Is there a metric Pipe thread???? I have never seen it if there is.
I worked evenings at a machine tool company in the early 1990s.One of the high ups thought that the change was so great he ordered all the drawing to be metric dimensioned only. Guess what. well over 50% of the machines in the entire plant where manual controlled machines. THEY HAD ENGLISH only hand wheels and such. So when you got a new drawing you had to set down and calculate every single dimension back to English. There was only ONE long bed lathe in the whole plant that could chase metric ball screws. They had to run it 3 shifts 7 days a week to met the demand. It took management several years to finally buy a few more Metric lathes.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
