Posted by JDseller on July 01, 2012 at 16:17:12 from (208.126.196.144):
In Reply to: Which grease? posted by dcarp on July 01, 2012 at 12:42:11:
I looked up the sheet on this grease. It would appear to be a better grease for sliding and pivot types of applications. The sheet says "Excellent adhesion permits it to have better "stay-ability" than most other greases" and "Because this product has better adhesion, it is a little more difficult to pump than less adhesive greases". So it would appear that this is a fairly thick grease. It also uses "Anhydrous Calcium" as its thickener. I would think anything with calcium would tend to setup. This "sticky" grease is not what you want in bearing and gear box applications. You want a grease that will soften and move toward any friction to lube it.
I switched to JD ploy urea grease ten years ago or more. It cost about twice what the regular grease does, $4.05 per tube, but it does not get hard in fittings and has water inhibitors. It is what JD recommends in the out board axle bearings on the row crop tractors. I am getting much better life out of all my bearing applications since I started using it. U-joints in my 4x4 pickups have had the best response I am getting 5-6 years out the front end joints now compared with half that with just a lithium grease. I rarely have a plugged fitting. Even in disk and things that set between usage a lot.
Here is a usage sheet on it:
Multi-Purpose SD Polyurea Gun Grease - TY6341
Features: Ideal in rolling-contact applications -15 to 350°F (-26 to 177°C) For high-temperature, extreme-pressure conditions Used for initial lubrication at the factory in U-joints and axle bearings For excellent protection in corrosive and wet conditions Compatible with most other types of grease Excellent for all-purpose applications, especially those requiring a severe-duty grease Our best multi-purpose grease Service rating: Equipment manufacturers' extended service intervals NLGI grade 2 JDM J13E1, J13E4, J13E5 and J25C GC-LB
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.