John Deere Tractors Discussion Board |
Re: unstyled A Gas tank cleaner
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by F-I-T on April 14, 2004 at 21:24:15 from (64.174.168.50):
In Reply to: unstyled A Gas tank cleaner posted by donwisc on April 14, 2004 at 20:27:48:
Don: Here's my standard remedy for cleaning out a tank. You may have to repeat parts of this procedure. Good luck! You can have three different things to remove in that tank: dirt, gelled/varnished gasoline, and red rust. Couple of things you don't want to do: 1) Disolve any plating (like zinc) from the inside of the tank 2) Make a near rust through hole a real hole. 3) Use acid so strong that you generate a significant volume of hydrogen gas... That's why I am not a fan of muriatic acid (a comon blend of Hydrchloric and Sulfuric acids) which some people advocate, except to clean masonry. Lately I have been doing the following: First, if accessible, insert a small length of chain to use as an agitator. Be careful to remove any tank gauge floats if applicable. If I think it's just old organic sludge in the tank, like boiled off gasoline, try acetone first (cheaper), then try MEK (Methyl Ethyl Ketone). MEK will do the job, but be sure to use it in a well ventilated area, eye protection, ....yadda, yadda....you know the drill. 2 quarts should do the trick. If dirt remains, it's probably water soluble, put a cork in the bottom, and fill with hot water and lye. Soak over night, drain, then power wash every where the nozzle will reach. If you then see any visible rust in the tank, go to the discount auto parts store, and buy some Phosphoric Acid. It's kind of greenish, and it is sold by them to treat (convert) free rust into the black iron oxide and iron phosphate. Now this stuff is dilute phosphoric acid, but remember, not all acids are alike. This stuff will eat metal, but at it's low strength, about all you will get is a good etch. It WILL turn the old rust black, and that rust patch will then be chemically inert. The tank must be oil free so the acid can get to the rusted metal, which is why I clean it with acetone or MEK, then the lkye, then maybe hot soapy water, or purple cleaner to remove the oily residue from the MEK and slop. Then slosh the phosphoric acid around. Be sure to wear protective clothing and eye protection, etc. (It will bite you nose !). Let it sit for at least 45 min or an hour. Letting it sit overnight won't hurt.
Now, rinse the tank with hot water, or even better, blast it with a power washer. Though they say it will dry to a sandable, primable finish, I like to remove the residue. If you do this, it will shine, and you won't have to worry that you removed too much base metal. After you wash it, slosh a bit more some MEK in it, and the remioander of the water will be displaced and will pool out the drain. If you are not going to install it for sometime, slosh some diesel fuel in it to oil the fresh metal surfaces because the MEK will have stripped all oil from the metal pores and it will begin to re-rust very quickly.. BTW: I treat my freshly sandblasted parts with this "Phosphatizing" acid, then power wash, dry, and prime. The acid kills any rust I missed, and disolves any remnants of silica from the sand exploding against the metal. Frank
Follow Ups:
Home
| Forums
Today's Featured Article -
Trailering Your Tractor - by Curtis Von Fange. One of the fun things of summer and fall are the parades and tractor shows that go on across America. Many owners of tractors travel long distances to attend these shows and they usually take their restored iron along with them. Safe trailering practices and inspections will ensure that the event is a fun one. A good habit to develop when using a trailer is to give that ‘quick look over’ before taking it on a trip. Before hooking up to it check the tongue for proper operation. The latche
... [Read Article]
Latest Ad:
Super WD9.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|