I made the baseball bat analogy earlier - maybe a sledge hammer is a better way to describe it.
Picture somebody hitting the crank with an all out swing of a 16 pound sledge hammer, in the opposite direction of your cranking.
Think about where you want your hand on the crank when that hammer hits.
It's really that forceful and instantaneous.
Best possible position is crank in short pulls from about the 7:00 to 10:00 positions.
I'd say the thumb position is LESS important if you're doing it that way (which IS the right way).
I think the thumb rule is more for those who insist on cranking further. if you go past 11:00 - the degree to which your thumb is going to be forced backwards into your hand depends on just how far past you go.
Once you come around to 3:00 or so - you're taking the full brunt of the hit into your extended arm and possibly body. that's where bones really start breaking.
Even if your lucky enough to have your hand come off without a hit - the crank can still be launched in the very wrong direction at that point. MUCH better to have it thrown down and away from you - which again - means 7:00 to 10:00 position.
This assumes you're standing forward and a little left of the crank (left, looking at the tractor), cranking with your right hand.
Don't mean to drone on about this topic - but it's so important to anybody who hasn't done it before. You don't have to fear it - but you do have to respect it.
Time the engine to fire slightly AFTER tdc (the click of the magneto - not running). There's absolutely no benefit to trying to hit tdc EXACTLY.
If you ever expect to hand crank even once - always err on the side of AFTER. you should have absolutely no doubt about it. If you're within 5 degrees after, it'll still start easily if everything else is tuned properly, so you've got a fair amount of wiggle room.
I know I'm preaching to the choir for the most part here. But I know when I first started looking for this info myself - I got a LOT of conflicting opinions. After a few kickbacks, I quickly weeded through which opinions were the best.
This post was edited by JRSutton at 11:53:46 03/19/13.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
