Apparantly all you are doing is scraping a little, sanding a little and washing the tractor. That is not nearly enough. You don't mention primers or surfacers. Clean EVERYTHING and then prime. It takes me hours or days to get a tractor clean. Wash the cast, wire brush it to bare metal, then clean it with soap and water, then wax and grease remover until the rags come away clean. Prime with epoxy primer, nothing else. Then topcoat. Don't be concerned with the flaws in the cast, they are supposed to be there. If it is really rotten, use a little body filler, but don't try to make cast perfect. On the sheet metal sand to bare metal -- ALL bare metal. Use body filler for any imperfections. Trade name BONDO is the poorest body filler made. Get some body filler from your paint supplier. Mix a little at a time, it is very sensitive to the amount of hardener. Use it until it becomes hard to spread, then make another small batch. The thinner it is the easier it is to sand, you may need multiple coats of it. Do as Gordo says regarding the sanding. When it is as smooth as you can get it, use epoxy primer (2 coats) followed by a Urethane (uses hardener) surfacer. Put on three coats about 10 minutes apart, let dry and wet sand with a block or a board if you want to do it as Gordo does. You may need to repeat the surfacer 3 or so times. You can add a small amount of whatever you are using for the topcoat (follow the instructions) to get a different color, that way you can see when you have sanded to the previous coat. Be prepared to take a lot of time. After that you can topcoat. If you did not do a good job it will show in the topcoat. Sand the bad areas, apply more bondo and surfacer, and remove as much of the previous topcoat as feasible and do the topcoat again. As to your pictures, if you can see imperfections in the photo, as Gordo mentioned about the fender, it is a lousy paint job. Regardless of the favorable comments, pictures are worthless, they simply do not show detail -- that has to be seen in person and is the reason some do not like your tractors. You need to take more time. There is a TON of info on the paint and body work forum on this site. Spend a day reading it. I apologize for the harsh answer, but you admitted your problems and need help.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Picking Corn - by Rick Nikolich. It was the day before Christmas shutdown at work and I asked our lead engineering expert Scott Andrzejewski what he was going to do over the holidays. He said that he had some corn that he still needed to pick with an antique one-row New Idea corn picker. Scott has a nice farm about an hour north of Lansing in St. Johns, MI. He wanted to get the rest of his corn in by the next day (Christmas Eve). We had about an inch of new snow on the ground and single digit temperatures. So in the bac
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
