Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

my opinion: 656 draft control leaks repair


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by karl f on July 21, 2009 at 22:39:20 from (172.129.7.49):

I did some research...in the book and inside the tractor.
Thanks for the input from everyone a few days ago.

Those with concerns about affecting the tractor like I had, do not worry about it because: a)the differential is lubed from the oil cooler circuit, which will not be affected from this procedure b) there will be a good dousing of oil inside the lift cover while the engine runs, and the remaining oil film coating shoud be sufficient to keep parts lubed while sitting over time. c) there is an added benefit of knowing you have drained ALL of the oil when you drain the transmission housing--otherwise you have to remove the seat, and the draft control cover and take the tall plug out, then put it back, and repeat at the next oil change.

There are 2 ways to do this. The first is remove the front plug as Allen and a few others have talked about. The second is to remove the actual drain pipe in the rear of the lift housing--I opted to do this but also replaced the pipe with a shorter one that will keep the oil about an inch deep, same as the front plug when removed. If you need to remove the cylinder assembly, you may as well remove the rear drain pipe. I decided this route mainly because it can drain off faster than the 1/4" pipe hole the front plug covers and because i had the cylinder out. bc had mentioned observing his cavity filling faster than the small front hole could keep up, and since the cquadrant leaks are from too high oil level, I think the larger drain out the back is the way to go since the oil will be less likely to bottleneck and rise. The rear drain pipe is only threaded on tractors with draft control. For those like bc, without draft control, you could maybe unbolt the plate from underneath and just let it dump out the 5x5 hole, or cut the tube short.

Now that I know how the thing works, I am not scared of this method and I will help recommend this modification to anyone with the 656 666 686 models.

-karl f
ps might be good info for 504 and 544 too, YMMV



Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy