Posted by ScottyHOMEy on June 14, 2009 at 12:06:54 from (70.105.238.74):
In Reply to: oil for Farmall B posted by Rossputin on June 14, 2009 at 10:47:42:
1)The main distinction between a B and BN is the widdth of the tractor, which varied by the length of the differential shaft housings, the castings between the transmission and the final drives. On a BN, those are 18" on each side, and on a B 22". This leads to other differences such as the operator/seat platform being only about 18" wide on the BN. And, if you don't have a tape with you, the easiest thing to spot is the right-hand seat support. On a BN, the right seat support is bolted to the flange on the end of the shaft housing, pretty much the same way the left bracket mounts to the tranny. On a B, the right support is mounted to a bracket that is bolted the platform. This applies as long as you have the standard seat supports, which yours appears to have. I agree, the serial number looks a little weird, the way it was stamped. How does the numerical part compare with the number on the motor?
2) Any good multigrade, 10-30 or 10-40 will be fine. Some folks swear by the 15-40 formulated for diesels, adn you can use straight 30, as well. Do a search on oil on this board and you'll find all sorts of long-winded threads about it, and even the detergent/non-detergent question. Bottom line it's your choice.
3) Coolant. Test whatever's in there, and go from there. If you don't have a tester, you can try to drain some into a jar and take to a garage, but there's a good chance the drain pipe is plugged with sediment. That will have to dealt with at some point anyway. Can't hurt and might help to just drain it, flush it and change it out with new, mixed at 50/50 using distilled water.
4) If this were a high-temp high-compression engine you might could maybe justify a lead substitute. It's not either of those. Plain old unleaded from the pump will do just fine. What I would recommend is that you keep your fuel tank fairly full if you're not going to work it regularly, just to cut down on the condensation.
And do get yourself at least the Operator's Manual. Well worth the price for the maintenance, safety and operation information.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
