Randy: That is exactly what I was talking about, and the original IH intent was nothing more than pinning the hitch bail up so it would clear high crops during use of center and rear cultivators. Usually the pull bar would be removed during cultivation.
As I said before, we pinned it up there for clearence when raking hay. Problem is that attachment is loose, thus one got the hitch bail slamming on bottom of platform. What we built was a round shaft cross member on front of final drives with a tee off it of stock same size as the draft link. By using several holes we achived height adjustment of the hitch bail.
By raising hitch bail and rear hitch we could straddle quite large hay windrows, when turning hay. More clearence over a windrow of hay than any other tractor we had on the farm, including 300, 560 and 656. The other function we found it valuable was the tool bar cultivator in 3 - 20" rows of rutabagas. We had center two bar tool bars and rear two bar tool bars with depth gauge wheels. The rear mounted set were fast hitch mounted. If one left the draft link in place, it tilted the back bars as the center bars lowered. This made shanks on back tool bar lift out of soil. Thus the fixed setting at front of hitch bail was quite important.
I found problems also with draft link in place while using front blade. These blades are plenty heavy for this hydraulic system lift via the rockshafts. If you place a counter weight mounted in fast hitch, (could include any implement, fast hitch mounted) this adds to weight front hydraulics must lift. My blade is somewhat heavier than the factory blade, and if I leave the draft link in place with 500# counter weight on fast hitch, my hydraulics will not lift the blade.
Bear in mind my 130 hydraulics are in good working condition, I can lift a 1,000 disk on my fabricated 3 point hitch. Those front blades create quite a mechanical disadvantage for the hydraulics. In fact I say every year, before another snow season, I'm going to install a remote hydraulic valve and use a remote cylinder to lift the blade. Problem is I get too busy gardening, and before I know it snow is upon me. Like the snow we got Thurs. night into Fri., 24" and it fell straight down with no wind. I have a 30" diameter, upright cylinder propane tank 20' from any building. Snow on top of it formed a perfect 30" cylinder, 24" deep. I never saw anything like that previous in my lifetime. Also been a few 4x12 pitch roof's gone down in the neighborhood, too much snow load.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
