Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Anyone need to run drawbar pull on their tra


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by El Toro on October 29, 2006 at 06:22:50 from (205.188.116.133):

In Reply to: Re: Anyone need to run drawbar pull on their tra posted by Randy as in Randy-IA on October 28, 2006 at 15:47:18:

Hi Randy, When we conducted drawbar pull test on a vehicle with a stick manual transmission we ran the test by engine speed. We would start at max rpm at wot and would drop the rpm's by 200 rpm's and when you do this the drawbar pull will rise as you go lower in rpm's. We would plot this on graph paper where rpm's versus drawbar pull. You will reach a point where you are at max drawbar as you keep dropping the rpm's. You will also notice as you go lower in rpm's the the drawbar pull will drop off at some point. When you reach this point there's no need to go lower in rpm's.
We would then let off on the load and go back to
max rpm's. Then we would run another set of readings using the same rpm's again. Then we would plot the readings to obtain a curve. We ran every gear and we ran full load fuel consumption too.

On some vehicles like your Farmall tractors that have the engine speed governed you won't be able to change the rpm since the governor cuts in to recover. We ran these by road speed starting at the max rs. We would drop the road speed by one mph until the max drawbar pull is obtained. The vehicle may start to lose traction and the pull will fall off. We would not go any lower in rs here. On the higher gears we ran by road speed
too, but we would quit when the drawbar pull dropped off. You don't want to overload your clutch by stalling your test vehicle and having the clutch smoking. The M7 has a calibrated 5th wheel for measuring road speed too. Hal


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy