Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Sorry! Our Phone System is Down. Please use our Contact Us Form.

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Living with a Baler


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Michael Soldan on August 31, 2006 at 17:50:44 from (24.235.41.226):

Welp, I got the Massey#10 out to do the second cut, started down a row and the first bale didn't tie...neither did the next twenty! Neighbours stopped in and had a look, offered some opinions, finally I said I would wait 'til the son-in-law got home from work. I worked in the barn for an hour or so, then decided I would have another look. I stood there studying the knotters for about 10 minutes and I noticed the little arm that rides the knotter was sitting out about a half inch from where it should be, poked with my finger and it snapped back into place..HMMMM..neighbours came in again and we decided to clean and oil everything associated with this arm and pivot, started the baler and did 240 bales with one miss...now go figure, the baler is always inside but it was definitely rust that kept it from functioning. I was ready to get the round baler out and get 'er done. I did want small squares to put up in the mow. On a freezing snowy blowing day I find it nicer to throw 8 or 10 small squares down that get the tractor out to get a big round out. This gives me around a thousand small squares the rest is rounds..anyway when a baler works right its a charm, when it doesn't it is the most frustrating situation..Oh yeah and I had just put a new tire on it($93) and 15 teeth @$4.09 ea..so I was expecting it to work..alls well that ends well....*^%&!% Baler!


Replies:




Add a Reply

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy