Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 1950 M ignition starting problem


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by John T on June 26, 2006 at 14:55:19 from (66.244.90.5):

In Reply to: Re: 1950 M ignition starting problem posted by jpl on June 26, 2006 at 09:45:06:

jpl n Rusty, If he happens to have one of those solenoids with the extra lil (I) terminal (like Ford n some GM used) its hot with full battery voltage ONLY when the solenoid is engaged (its cranking) and thats good for and used when one uses a 6 volt coil with an "External" Ballast Resistor on a 12 volt tractor. What it does is effectively by pass the ballast and apply full unballasted battery voltage to the coil (ie. 12 volts on a 6 volt coil) ONLY while cranking. Thats what some farmers call a "start on 12 and run on 6 coil system"........HOWEVER if theres no external ballast to by pass, the solenoids lil extra lil I terminal (or any other terminal for that matter) dosent apply any more voltage to the coil (assuming switch n all else is okay) then what normally comes from the regular ignition switch feed.

HOWEVER if the switch contacts (resistive/carboned/loose) or the switch wiring is bad, the extra lil jumper wire to the coil could help and it cant hurt nuttin so its worth a try BUTTTT its not the normal or factor way, it is the factory way when they use a 6 volt coil on a 12 volt tractor with an external ballast and want to improve the starting spark energy and yessssss it works great.

Bottom line is its NOT ordinary but it cant hurt and might actually help as a band aid approach (but he needs to fix the REAL problem) if the switch or wiring has some resistance and is dropping voltage.

Fun chat, yall take care n God Bless

John T


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy