Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: further 656 wiring issues


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Janicholson on May 13, 2006 at 07:07:10 from (66.173.50.123):

In Reply to: further 656 wiring issues posted by charleskirton on May 12, 2006 at 14:56:20:

An engine that runs on start only is pretty easy to diagnose. It is running because the ballast resistor bypass wire is doing its job. It is stopping because the "run" ignition circuit is "open". Put it in neutral, turn on the switch to run (not start) check for volts at the coil (supply side, not dist side, and the other lead of the volt meter to good shiny ground). If none, my theory is correct. If none, follow that wire to the ballast resistor. check for volts there at the terminal that wire connects to (there may be another wire there as well, ignore it). If volts, the wire is bad internally. If none, check for volts on the opposite side of the ballast resistor. if volts, replace theresistor, and you are set to go. If no volts, follow that wire to its other end and check for volts. If volts there that wire is bad. The wiring on your tractor may include switches and safety devices so tracing the wire may require effort. Eventualy the circuit will get back to the ignition switch terminal that is ign. (hot when in the run position. if this has no volts, the switch may be bad, or the supply to the switch may be disconnected. If the start on this tractor is like on a car by turning the key switch to start, the switch is bad. If it is by push button, the supply to the switch is faulty.
I hope this allows you to diagnose the problem.
keep un informed as to what you find, it is as important as our messages to you.
JimN


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy