Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: super m coil problems


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by ChadS on March 06, 2006 at 07:33:17 from (66.228.96.240):

In Reply to: Re: super m coil problems posted by John T on March 06, 2006 at 04:58:24:

Is the generator hooked up? If it is, did you convert it to 12 volt? Im not sure if the hot wire comes off the generator wiring somehow,, but if it does, and your putting 12 volt to a 6 volt generator,,, you may be creating a short in the wiring. But, that is if the IGN wiring is incorporated into the charging circuit, and still using a factory wiring harness. You have to cut the voltage back on the hotter coils when using points. When you dont, it overpowers the condensor and fries the point contacts. its also more prone to arc across the point gaps, and have a short in the distributor cap, causing the electricity to jump around inside the cap. Ive ran a MSD blaster 2 coil on my 460 with points, and always ran a resistor in the power wire. Never had problems with points burning up. If you run it for a while, just like it is,, let it run for abut 5 or 10 minutes, shut it off, then touch the coil. Careful!! It may be hot!! if it's hot, you need to put in a resistor. When the coils get hot, they short out, and can be dangerous and explode. You really cant get much more voltage to the plugs when using points, the condensor stops you everytime. Best to use electronic set up to get the best voltage to the plugs. Lokk at the plugs while your at it. New engines will have shavings from the rings seting in and can get in the electrodes and short out plugs. ChadS


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy