Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Super M disc brakes


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Bob M on February 15, 2006 at 05:48:03 from (151.190.254.108):

In Reply to: Super M disc brakes posted by Jim in NC on February 15, 2006 at 04:30:19:

First disassemble and THOROUGLY clean all the parts. Pay special attention to:

- The 3 balls and the ramps in the actuating plates the balls run in. All must clean (and the balls be shiny) and rust free.

- Machined surfaces of the reaction lugs on the outer edge of the actuating plate assembly and the mating lug surfaces on the inside the brake cover.

- Brake shaft splines. If there’s any burrs, etc on the splines file them smooth.

- If the rotating disk friction material shows signs of oil/grease contamination, toss ‘em and buy new ones.

- If the friction surfaces on the actuating disk, the inside of the cover and against the tranny have rust, scale, etc. use sandpaper to clean them down to bare metal. Or have a machinist take a light cut on each piece – but just down to bare metal.

---

When reassembling the brakes use a LIGHT film of Nevr Seez or similar on the splines and the actuating disk lugs. A bit of powdered graphite or moly powder is good in the ball ramps. And a drop of oil on each pivot point on the actuating assembly. However keep all lubrication to a minimum – you don’t want excess lube getting onto the friction surfaces!



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy