Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 12 Volt for Farmall C (Bob M)


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by John T on November 28, 2005 at 12:37:02 from (66.244.90.98):

In Reply to: 12 Volt for Farmall C (Bob M) posted by DelMN on November 28, 2005 at 11:56:52:

Del, I dont have Bobs schematic handy, but I know hes about the best source Ive seen on these farmalls and would believe n trust regarding their wiring. Believe him before meeeeeeeeeee.

That being said, is there EITHER a 10 ohm current limiting protection resistor in your alternators excitation circuit from the coils high input side or the ignition switches output ORRRRRRRRRRRRRRRRR a 5 amp 50 PIV volt diode TO THE LIL SIDE NO. 1 ALTERNATOR TERMINAL?????

CUZ if not, when you trun off the ignition switch the alternator is back feeding the coil and keeping voltage to making her still run EVEN WHEN ITS SWITCHED OFF

I highly recommend a 10 ohm resistor in the circuit that excites the alternators lil side No. 1 terminal for protection. although she may be fine forever even without it, better safe then sorry I say. Thennnnnnn if she still back feeds the coil and runs when shut off, simply add a 5 amp 50 PIV volt diode (one way current flow check valve) in series in the circuit after the voltage feed (coil or switch) and before the alternator to stop that run on problem. NOTE the diode MUST be wired + from feed and - to alternator so it can feed current into the alternator BUT NOT allow it to flow out of the alternator to feed the coil.


Soooooooo, do you have a diode or a resistor in the alternators lil No. 1 excitation circuit???????? If not, therein lies the problem of why she runs even after shes turned off. The diode dont really need to be 5 amp rated, thats just what I use as its easier to wire.

See what Bob n the other good gents have to say.

John T


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Box Plow Blues - by Tom Schwarz. One of the first implements most tractor owners obtain is the box plow. For very little money, this piece of equipment promises to plow and flatten any hill or vale on your ranch road or farm. At least that's what I thought! As simple as a box plow appears, it can be rather challenging to make work correctly. In our sandy soils of Florida, traction is king. You can never have wide enough tires or heavy enough weights to get all the traction you want … unless you own a monster tractor. U ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy