Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 43 Farmall H charging question...


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by farmallhal on July 06, 2005 at 11:38:56 from (64.24.35.16):

In Reply to: 43 Farmall H charging question... posted by Jesse on July 05, 2005 at 15:50:16:

Jesse, A Hitachi #14231 is the alternator to use. It is about an inch smaller in diameter then a Delco 10-SI and you need every bit of room you can get under the hood on the H which will be tight. I turned my existing generator bracket upside down which allowed me to retain the existing generator belt with my alternator. The alternator cost right at $50 plus a $10 core charge. I got mine at O'Reilly's Auto Parts but they are available at NAPA and other auto parts stores as well. It is an alternator used on a 1978-1980 Nissan 620 or 720 pickup with a 2 liter engine. It is a 3 wire alternator with a built in regulator and was very easy to wire in using Bob Mehville's wiring diagrams here on this site. My alternator terminals were labeled "L" and "S". "L" is same as 1 in Bob's diagram and the "S" is the same as 2. You will need to install a washer between the pulley halves for the wider IH generator belt. It works very well and starts charging when the engine is started. I also used a Radio Shack 10 watt/10 ohm resistor in place of the light shown in Bob's diagrams as I had trouble locating the noted light and holder. You will have enough room to adjust the belt tension a little bit since turning the generator bracket upside down moves the alternator upwards about an inch which takes out most of the slack. Good luck and it should go fine. Send an email if you require additional information.


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy