Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 560 Questions


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by captaink on February 03, 2005 at 09:09:18 from (66.115.214.56):

In Reply to: 560 Questions posted by Eric E on February 03, 2005 at 07:03:50:

When you were told “pinion gear” were you told which one? There is a pinion shaft that drives the ring gear on the differential, there are also two pinion shafts that dive the “bull gears” or final drive. The one that you are referring to is the one that drives the “bull gear” on the right side. The PTO hole that Aces is referring to is where the PTO unit is bolted into the rear end of the tractor. After the PTO is removed, you can see and reach into the rear end of the tractor at least somewhat. The casting you are working on needs to have the bull gear removed from the axle and moved rearward enough to clear the part of the housing with the inside bearing for that pinion shaft.

My suggestion is to go ahead and pull the cover off the transmission/differential. It will take more time, but he work will be less frustrating since you will be working from the top rather than through a small opening. Get a shop manual to help out, and by the way, this will not be a quick deal. That way you can inspect gears, bearings, and replace any defective parts found.

Now, before you get really gun-ho, take the cover off the top of the mid section (TA) of the tractor and check the small clutch under the cover. If this clutch is shot and the TA ramp and roller clutch has failed the tractor will not move. The clutch under the cover drives the whole tractor (through the TA planetary carrier) and if it is out, then power is transmitted through the planetary gearing. If the ramp and roller (overrunning) clutch has also failed, the planetary carrier will spin backwards and the tractor will not move.

Hope this helps.



Follow Ups:




Post a Followup

:
:
Hide: Yes No
Hiding your address protects you from spam generators but allows you to receive email response notifications.

Subject: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy