Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Age of McCormick-Deering 10-20


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob Kerr on March 04, 2004 at 20:45:05 from (64.12.97.12):

In Reply to: Age of McCormick-Deering 10-20 posted by Gary S. on March 03, 2004 at 10:36:07:

Most of the ones I have seen that have the exhaust that goes through the firewall (or front tank support)were built between 27 and 28. The earlier ones have 2 exhaust pipes that are just below the carb, one large dia and one small dia, and the 29 up manifold has the switchable baffles to run either gas or kero. If you get yours running it may not run good on gas when hot, just try kero in it as that is what those early manifolds were made to run. Mike is right about the serial number but I can add a bit to help you locate it, it is close to the lower water neck. I have seen a few though that were not stamped and they may have had the engine changed with a new on from the factory. I personally own 2 10-20 parts tractors that have had the engines switched from one to the other, luckily I bought those same two tractors at that auction, there were about 5 10-20s there! See if the serial number is on the boss, post it and one of us can give you the year and then check the date on the main frame casting, they should be pretty close. If all that fails, get a parts book and start looking up part numbers on everything. There were changes made all through the production even in mid year and the serial numbers for changes are listed. A couple things I can think of are the gear shift lever, in 29 was straight with no knob cast in and the older ones have a small knob, also the spark and throttle lever guide on the older ones have a small "arrow" cast in where you set the spark lever for starting, and the later ones don't have the arrow. Carbs another good place to look for numbers and were not too likley to get replaced since they are easy to work on. Mags are a bad place to get numbers since so many were exchanged over the years. You can really almost pinpoint the time the tractor was built down to the week, that is if it didn't have a bunch of parts replaced years ago. Some did, some didn't, depended on how hard they were used and how good of care was taken. Good luck!


Follow Ups:




Post A Followup

:
:

: Re: Re: Age of McCormick-Deering 10-20

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy