Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: To rebuilder smta ta


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by rebuilder on December 17, 2003 at 18:54:55 from (66.228.102.32):

In Reply to: To rebuilder smta ta posted by paul on December 17, 2003 at 17:49:04:

Paul: I done quite a bit of thinking on what might be the primary reason for your low side noise. I have to believe that since it only occurs when T.A. is engaged the problem is contained within the T.A. Perhaps somone else on the forum can back me up on this. My gut feeling right now is that a needle bearing is going out possibly inside the primary shaft(sun gear). I have never seen the two bearings in the carrier go out, just show some wear. Is the throwout bearing bad can you tell? The only other answer would be the ramp cams have become soo worn that they are grinding against the carrier when engaged. I have seen the needles seize inside the planetary gears but only rarely, and if you have taken good care of changing the oil and keeping the level up this should not be your problem.

SO- I guess I haven't helped you a whit in narrowwing down the problem without tearing the T.A. apart. Check the Throwout bearing while you have the top plate off although you may not be able to tell easliy if it is going out.

Also- before you split the tractor, try doing what Kelly C did and remove the belt pulley or the plate covering the belt pulley hole in the speed transmission tho get a look at any damage to the gears that may be there(see posts a couple of days ago)_.This may give you some more clues to your noise. Good luck and don't hesitate with more T.A. questions.!


Follow Ups:




Post A Followup

:
:

: Re: Re: To rebuilder smta ta

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy