Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: 404 farmall flywheel


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Hugh MacKay on July 20, 2003 at 09:08:24 from (209.226.106.125):

In Reply to: 404 farmall flywheel posted by J in Pa on July 19, 2003 at 15:13:57:

J in Pa: I just went through the IT service manual and I can't see any mention of the pilot bushing. I have never had anything to do with 404, however the 100, 130, 140, 200, 230, 240, 404 and 2404, using C-123 and C-135 engines are covered in same IT manual and while cranks are different I suspect only difference is throw the C-135 having longer stroke. I have changed clutches in a number of C-123 engined tractors, and very seldom have I even changed the pilot bushing, as they aren't usually very troublesome.

One item I did notice is use of hydra creeper drive. If you are not familiar with it, a hydraulic motor that goes on pto and is driven by a remote outlet valve on tractor, and moves the tractor at a fraction of it's regular speeds via the pto and transmission. During use of this attachment tractor clutch pedal is held depressed. They make mention this requires a special release bearing as it is always turning while hydra creeper is in use. The same would be true of pilot bushing, and one would think a bearing would be required in place of bushing. Do you know if your tractor was ever used this way. My thoughts being that someone used this a lot, and shaft is worn where it enters pilot bushing. Have you ever checked this shaft size in relation to a new bushing? I am not suggesting I am right, but just a thought when going through IT manual and coming across this section on the hydra creeper drive.


Follow Ups:




Post A Followup

:
:

: Re: Re: 404 farmall flywheel

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tractor Profile: Allis-Chalmers Model G - by Staff. The first Allis-Chalmers Model G was produced in 1948 in Gasden, Alabama, and was designed for vegetable gardeners, small farms and landscape businesses. It is a small compact tractor that came with a complete line of implements especially tailored for its unique design. It featured a rear-mounted Continental N62 four-cylinder engine with a 2-3/8 x 3-1/2 inch bore and stroke. The rear-mounted engine provided traction for the rear wheels while at the same time gave the tractor operator a gre ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy