Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Re: Re: Super C motor oil


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Steve - IN on June 17, 2003 at 21:53:19 from (12.223.205.149):

In Reply to: Re: Re: Super C motor oil posted by Doug in OR on June 17, 2003 at 17:16:07:

Doug,
I think we've had this discussion before -- maybe a year or two ago. I basically agree with you.

I've used synthetics since ~1975 for some engines. On race engines, they run 20 to 30 degrees cooler on an oil temp gauge, and they do dyno slightly better. The amazing part is when you tear down an racing engine that's used synthetics from the get go and see the bearings -- they look like you just installed them.

I use synthetics in 4 of my 5 tractors. The fifth one is the rub, I need to do a rebuild on it, and it would just burn off that nice expensive synthetic oil. So in the meantime, I'm using straight 30W and now 40W as it's gotten warm. You're absolutely right about cold starts -- but there is a trick known to lots of guys who went to flight school 30 or more years ago on piston engines. Leave the switch off - pull through the engine -- manually or with the starter, until oil pressure builds. Then go switch on. That mostly eliminates any cold start problem. If I use this engine when it's cold; then I'd use a 10w-40. 'Til then I get to turn it through then yell clear when I switch on.

Guys who went to flight school less than 30 years ago quickly went into turbines and synthetics. There's nothing better for standing up to cold starts and also outrageous temps and revs. Next time this discussion comes up - maybe we should ask if someone would use 30W in an engine that turns >60,000 RPM at 20 below zero. If the answer is no - somebody has learned to appreciate synthetics.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Super C motor oil

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy