|
Farmall & IHC Tractors Discussion Board |
Re: Painting Questions
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steven@nd on June 08, 2002 at 20:37:25 from (12.23.184.103):
In Reply to: Painting Questions posted by K.B. on June 08, 2002 at 18:33:19:
It all depends on how you want your tractor to look when you are done. Time is the biggest thing when painting. More time = better quality. Especially prep time. Make sure you have a smooth surface for the primer to stick to: sand to bare metal on parts that have paint chips or loose paint, where the paint is still sticking to the metal good all you need to do is scratch it up so the primer will have something to stick to. I use a $150 High Volume Low Pressure gravity feed paint gun. It works great. However, I have also painted using a $20 1 pint touch up gun and also had great results. I use PPG paints. They have an excellent epoxy primer that does not require sanding before painting, and if you have a few dings you can prime, sand, and reprime to fill them in. For the final paint I use the acrylic urethane paint. It covers really well and paints easy and dries quickly. It can get expensive ($50 a pint for some shades of red, plus reducer and hardener). I always use hardener or else you scratch the paint when you lay a wrench on the hood. Another tip is to use the wax and grease remover from your PPG dealer, it removes all fingerprints, oil, etc. that will mess up your paint job. I use it before priming and then again on the primer before painting. You can certainly use CaseIH or your local farm and fleet store paint with no primer, but don't let your tractor sit outside very much. After a couple years it will look like this: 
kinda pink, huh?
Or you can put in some extra prep time and some extra $$ for the PPG paint and have a tractor that still looks like this after sitting out for 2 summers: 
Also, here is our truck we painted 5 years ago or so with PPG paint and it has NEVER been inside 1 day since then:
As with anything in life the time and money spent will determine the final product. Steven
Follow Ups:
Home
| Forums
Today's Featured Article -
Ford N-Series Transmission/Hydraulic Fluid - The Full Story - by Llamas. The transmission fluid in an “N”:-series tractor lubricates the transmission, differential, rear wheel bearings, PTO and hydraulic pump drive, and it also cats as the working fluid for the hydraulic lift. In 9N/2N models, it also lubricates the steering sector and shaft system. The owner’s manual for the 9N and 2N models specified the use of only two fluids. They were STRAIGHT MINERAL OIL SAE 90 (above freezing) and
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
