Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Wheel bearings/seals: Can anybody help?


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bruce on May 18, 2002 at 05:35:21 from (216.179.1.173):

I'm replacing the front steel wheel hubs with round spoke wheels on my F30. I noticed that, even though the bearings are the same, the inside diameter of the round spoke hub is smaller than the steel wheel hub. Both hubs have a "ring" that is pressed into the hub on the inside end. Is this called the felt seal retainer? When taking off the steel wheel hub, I found an oil seal and a felt washer behind it. However, when I put the inner bearing on the axle and tried to put the round spoke hub on the shaft, it wouldn't go on because the seal wouldn't fit in the hub. Since I had a new felt washer and oil seal, I removed the original one (destroying it in the process),and removed the ring (retainer) from inside the hub, which I don't think I should have done. The round spoke wheel is now on, but does not turn freely. THe bearings are not too tight,
but I think the drag is caused by the new seal and felt washer, which is turning when the hub turns. Is it supposed to do that? Also, which way does the oil seal go on? I have it with the flat side out and the indented side facing the felt washer. I'm stumped as to how all this is supposed to go together and work. It looks simple enough, but I just don't get it. Any help would be highly appreciated. Pictures too, if possible.My F30 parts manual doesn't give a very clear picture of this.


Follow Ups:




Post A Followup

:
:

: Re: Wheel bearings/seals: Can anybody help?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy