Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Got my MD home today!!!


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Haas on May 21, 2007 at 06:57:58 from (12.65.54.171):

In Reply to: Got my MD home today!!! posted by jonnnny2006 on May 20, 2007 at 23:29:54:

Be aware that the magneto rotates counterclockwise(facing the rotor), opposite to what you normally expect. So..you need to connect the plug wires accordingly. Have you checked the points to see that they are properly set?? If you got a shock, I would think the mag only needs some tuning up. Also, the point cam in the mags has only two lobes, so there is gearing between the cam and the rotor. You must have the timing correct so that the rotor points to No. 1 plug wire contact when the No. 1 cylinder is TDC of the compression stroke. Be aware that on the MD, changing to gas side does four things. 1) changes butterflys in the manifold to direct air through the carb. In diesel mode, air does not flow through the carb. 2)Turns the ignition on. That is ungrounds the mag. In diesel mode the mag is grounded to stop the spark. The switch is in a chamber at the front of the manifold. 3)Releases the carb float to allow gas to flow. On the diesel side the float is locked up to stop gas flow. 4)Opens the compression release valves to the spark plug chambers to reduce compression. In diesel mode, the valves are closed. Also, check the plugs to make sure you have the correct long reach Champion D89 plugs. These have a long electrode to facilitate combustion in the chamber that is restricted. They will cost around $8 each. When you have everything right, the MD should start in gas mode with only a turn or two. Mine requires full choke to start and then fiddle with the choke as it warms up. There is no throttle control except by removing the carburator and adjusting a plate inside. Keep us posted.




Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Picking Corn - by Rick Nikolich. It was the day before Christmas shutdown at work and I asked our lead engineering expert Scott Andrzejewski what he was going to do over the holidays. He said that he had some corn that he still needed to pick with an antique one-row New Idea corn picker. Scott has a nice farm about an hour north of Lansing in St. Johns, MI. He wanted to get the rest of his corn in by the next day (Christmas Eve). We had about an inch of new snow on the ground and single digit temperatures. So in the bac ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy