Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: SMTA Hydraulic Pump/Reservoir Removal


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by D Slater on February 20, 2007 at 20:10:53 from (152.163.100.199):

In Reply to: Re: SMTA Hydraulic Pump/Reservoir Removal posted by sflem849 on February 20, 2007 at 18:59:36:

Rear support for MTA without hydraulic would be like looking for a needle in haystack.They are something like a M or SM support and bolt in same place on top cover. At top a metal strap extended far enough forward with a hole to line up with gas tank stud then was bent to go back down to support at a angle as a brace.If you could find one from a Stage 2 without live hydraulics and modifiy to work it would have the bracket for starter and choke rod on it.If not a M would do. The distributor drive housing you need will be found on some 50 model M and 51 through 450 gas if not equiped with pump. The housing will have # 354951R1 on it if memory is correct. There's a position that distributor drive is supposed to be set, but it realy doesn't matter on getting in time as most are not set that way any more.after removing distributor cap all you need is to mark which dirrection rotor is pointing and never move engine while apart.After removing dist. from back of pump notice which way slot is pointing and try to put dist. drive housing in with slot as close to same dirrection as was. Next put dist. on and see if rotor lines up to mark on body you made. If its off very mutch you can remove and pull the T shaped gear driving dist and move it ever how many teeth it takes to get rotor back to mark. At last to get exact you may have to loosen 2 clamp bolts and fine tune dist. housing. When you switch gears and shafts they usualy don't line up exact same without turning dist. body some. One other tip the lower inside bolt that you are using to bolt drive housing to front cover, make sure its not to long as it will contact cam gear on inside if so.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Choosin, Mounting and Using a Bush Hog Type Mower - by Francis Robinson. Looking around at my new neighbors, most of whom are city raised and have recently acquired their first mini-farms of five to fifteen acres and also from reading questions ask at various discussion sites on the web it is frighteningly apparent that a great many guys (and a few gals) are learning by trial and error and mostly error how to use a very dangerous piece of farm equipment. It is also very apparent that these folks are getting a lot of very poor and often very dangerous advice fro ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy