Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

More then you probably want to know


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by jdemaris on January 19, 2011 at 09:54:17 from (72.171.0.142):

In Reply to: Silly question about block heaters posted by Brad Gyde on January 19, 2011 at 07:28:54:

I checked around in my "junk box." I've got four new Champion CH77 glow-plugs and four new Delco 9Gs. You can't use the 9Gs, but the CH77s are fine.

I checked the specs and the Champion CH77s should be fine for your 6.9. If you want them, pay the postage and I can stick them in the mail.

To be honest though, the Beru plugs that Ford sells are much better quality and are pretty-much burn-out proof. That's what GM sticks in Delco boxes also.

I suggest you hook power to each plug though an amp-meter- just for a second and check amp draw on each plug. That will tell you if bad or not.
Your plugs are rated 9 amps.

Ford-IH up through 1986 takes plugs with these stats. If you were using Delphi brand, your truck takes a HDS305. Made for a "12 volt system", plug marked "6 volts", operating voltage is 9 volts, draws 9 amps, takes 50 seconds to reach full heat at 6 volts, threads are 10 mm X 1, heater-element depth is 26.5 mm.

HDS305 12 6 9 <50 @ 6V <50 @ 6V .375" 10 x 1.00 80 mm total length, 26.5 mm depth

The Champion CH77 is built to the following specs:

HDS306 12 6 9 <50 @ 6V <50 @ 6V .375" 10 x 1.00 77.5 mm total, length depth 26.5 mm depth

They are exactly the same except the Champion stands out a little taller by 2.5 MM (3/32").
The installed depth of the heating element is actually the same length.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy